A quiet oil-free compressor built for rooms where noise is not welcome: laboratories, clinics, classrooms and shared workshops. 1450W, 15 litres, 8 bar — plugged into an ordinary 220V socket.
Key figures for the SP-15S silent air compressor.
| Model No. | SP-15S |
|---|---|
| Rated Power | 1450 W |
| Working Pressure | 0.8 MPa (8 bar / 116 PSI) |
| Air Displacement | 118 L/min |
| Motor Speed | 2800 r/min |
| Voltage / Frequency | 220V / 50Hz, single-phase |
| Tank Capacity | 15 L horizontal receiver |
| Pump Type | Oil-free dual-cylinder |
| Noise Level | Approx. 60–70 dB(A) with GT silencer |
| Control | Auto start/stop pressure switch, regulator, gauge |
| Protection | Overload protection, solenoid valve, dual capacitor |
| Indicator | Intelligent digital voltage display |
| Dimensions | 47 × 20 × 55 cm |
| Mobility | Carry handle, anti-slip rollers, rubber feet |
Values are for reference and taken from the factory product sheet — confirm final figures before ordering.
Most compressors are built for a workshop corner and apologised for everywhere else. The SP-15S silent air compressor is designed the other way round: it assumes you will run it in a room with people in it. A GT silencer on the intake, an acoustically shrouded pump deck and anti-vibration feet bring running noise down to roughly 60–70 dB(A) — about the level of two people talking — so the unit can sit in a laboratory, a clinic corridor, a classroom or a flat-share garage without anyone asking you to switch it off.
Quiet is only half of what indoor users need. The other half is clean air, and that comes from the oil-free pump. With no oil in the crankcase there is no oil mist in the output: instrument air stays dry and uncontaminated, benches and finished surfaces stay free of spotting, and there is no oil level to check before every session. For labs, dental and optical work, electronics assembly and food-adjacent tasks, that removes the filtration stage — and the ongoing cost — that a lubricated compressor forces on you.
The rest of the machine is built to stay out of the way. An intelligent pressure switch starts the motor when the tank drops and stops it at the set point, so the compressor is simply ready whenever you reach for the trigger, and silent whenever you are not drawing air. A digital voltage display keeps watch on the supply, while a solenoid valve and dual capacitor protect the motor against back-pressure and electrical overload. At 47 × 20 × 55 cm it occupies less floor than an office chair.
How the SP-15S keeps the noise down and the air clean.
A dedicated intake silencer plus filter media is the single biggest reason this unit runs at conversation level instead of the 90+ dB of a bare piston pump.
The dual-cylinder pump sits inside a closed acoustic cover that contains mechanical noise at source rather than letting it radiate into the room.
Running noise lands in the 60–70 dB(A) band — quiet enough for teaching labs, treatment rooms and shared buildings during working hours.
Self-lubricating seals mean zero oil carry-over. No mist in the line, no contamination of instruments or finishes, no oil disposal.
Rubber feet and a stiffened receiver stop structure-borne hum travelling through floors and benches — often the most annoying part of a compressor.
The pressure switch manages the cycle on its own: it refills when the tank falls and rests when it is full, so the motor never runs longer than the job needs.
Live supply monitoring on the control head warns you about unstable mains before it takes a toll on the motor windings.
A solenoid valve unloads back-pressure at switch-off and a quality capacitor absorbs electrical stress — protecting the motor on both sides.
A thickened 15-litre tank with dual inlets refills quickly and buffers demand, keeping the motor's run time — and its noise — as short as possible.
Where a quiet, oil-free 15L compressor changes what is possible.
Clean instrument air without an oil-removal stage, at a noise level that does not disturb readings, meetings or adjacent offices.
Oil-free output and low running noise suit single-point air tasks in sensitive environments. For continuous multi-point supply, step up in the range.
Safe to run while teaching: quiet enough to talk over, no hot oil surfaces, and a household 220V plug instead of an industrial supply.
Appliance repair, electronics, model making and light assembly in buildings shared with other tenants — no complaints, no oil on the bench.
Oil-free pumps remove the most common rental failure — neglected oil — and quiet units generate fewer noise complaints from client sites.
Spare-part kits for switches, silencers, hoses and valves ship with your orders, so serviced units return to work the same week.
It is roughly the level of normal conversation or a busy office. A conventional piston compressor of similar output typically runs 85–95 dB(A), which is the range where hearing protection becomes necessary. The SP-15S can be used in the same room as other people without raised voices.
It is built for intermittent duty: the auto start/stop switch refills the tank and rests. That covers instrument air, blow-gun cleaning and intermittent tool use well. For a continuous, multi-outlet supply feeding several stations at once, choose a larger model in the Nantong Shengqiang range — we will size it against your total consumption.
The pump introduces no oil into the air path at all, which removes oil mist as a contaminant. Air still carries ambient humidity and dust, so for critical instrument or optical work pair it with the appropriate dryer or particulate filter — the compressor simply does not add oil to the problem.
Quite a lot. The 15 L receiver stores air so the motor runs in short bursts instead of continuously. Because the pump is the noisy part, a buffer tank directly reduces the amount of time you hear it.
No — 1450W on a standard 220V/50Hz single-phase socket. The built-in digital voltage display shows supply quality live, and the dual capacitor protects against overload, which is useful in older buildings with variable mains.
Drain condensate from the tank, keep the intake filter clean and check the silencer occasionally. There is no oil to change, no belt to tension and no lubrication schedule.
Yes. OEM private labelling, custom colours and packaging are supported, with compact export cartons designed to maximise container loading for distributors.